Riding into Fall!

 

 This morning was glorious; temperature was a very nice 67 degrees Fahrenheit (19 C) as I strapped my lunch onto the back of my old CB to come to work this morning. Later today the temperature is supposed to be back up to 90 but this morning gives the first hint of better days to come.

 Everyone knows that these old Hondas are aggravatingly cold natured even when bone stock in excellent condition. When you throw on a set of pod filters & a header you exacerbate this trait to the point that you have to be patient & let it warm up well before trying to move it. But to me it’s worth it just to hear that intake moan when you twist the right grip in anger. Properly set up on a well-tuned bike these old Keihin carburetors have a throttle response & drivability that rivals modern fuel injection, once the engine is up to operating temperature.

 After kissing my wife and telling my dog goodbye, I close my modular helmet and back out of the carport. After pushing down on the shifter and hearing the satisfying snick of first gear engaging,  I let out the clutch and head for the gravel road at the end of the drive. There are days when I miss my old Ninja & its ability to snake down a twisty paved road seemingly by thought command, but today is not one of them. On this scrambler I run twice as fast through the loose rocks and deep sand leaving my home.

 Upon reaching the pavement after looking both ways I pull out and make a quick run up through the gears relishing the delightful mechanical concerto that only an old four banger can play, especially when it is sucking in cool dense air through a set of K & N filters. It may just be in my head but to me every motorcycle I’ve ever ridden feels more powerful & somehow more alive when the weather starts to cool and the air gets denser.

 Leveling out somewhere around the speed suggestions on the road signs the cool damp air pushing through my mesh jacket gives me a little chill that is so enjoyable after the long hot summer. Right now the relative humidity is somewhere around 98%, later today when it gets hot again that will be miserable but this morning it is invigorating and I roll on the throttle some more  just to enjoy it. On days like this it is so damn good to be alive.

 Normally I try to leave the house at least 15 minutes earlier than I actually have to just because it makes such a huge difference in the traffic I encounter. Turning left off of the two lane blacktop onto a four lane highway.  I cruise toward the first small town that I will pass by on my little commute. Traffic density picks up a bit especially in the school zones, but all of the early risers don’t have to be in such an all fired hurry to get to work because they have plenty of time, so everyone is nice & polite making the drive pleasant rather than stressful. Leaving the bypass I turn down another two lane road that starts out rural but quickly turns into a crowded suburban neighborhood as you get closer to the city of Florence. Since I am early it is nearly empty, but in another 20 minutes navigating this particular road will be like driving through a pinball machine.

 There is a dense fog settled in over the little town of Quinby as I pass through, the mad commuter rush to work and school is just getting started. Visibility is maybe a half a mile and I frequently have to wipe my face shield & look out for the cages that do not realize they become invisible in the fog without their lights on. Leaving this town behind I turn right and head towards my final destination with my speed adjusted for the fog. As I am cruising along that “driver” comes flying up behind me out of the fog with no lights on of course. Young, female & aggressive, she is piloting a typical 10 ton SUV, while deeply engrossed in a conversation on the phone that she is holding up to her ear with one hand. Since there was no traffic in front of her, and she hasn’t looked at the speedometer since she got in the car she has no idea how fast she was going. Blissfully unaware that if I have to panic stop there is no way she could possibly stop fast enough to keep from running over me she pulls into position about 25 feet behind me and stays there. On one long straight stretch I deliberately slow down hoping she will pass but she doesn’t. There is no malice in her heart toward me she is just indifferent to the act of driving. I’m not in her way; she is just using me as her speedometer instead of hanging up the phone and looking at the one in her dashboard.

 Coming into the last residential neighborhood I slow down to just below the posted speed limit mindful of the numerous children waiting for the school buses that are out in the fog and ten ton Tessie in her giant white death tank actually pulls to within fifteen feet of my taillight. Knowing there is a very rough triple railroad crossing set into a high hump coming up shortly I get ready. Normally I’d slow down for this crossing but am kind of afraid to do so this morning, but hey I am riding what is basically an oversize dirt bike so at the approach to the track I stood up and gassed it sailing across the tracks and feeling nary a ripple.

 Behind me the Stupid Useless Vehicle slammed into the foot tall hump and its driver was no doubt smacked around inside of it as she panic braked across three rough train tracks. For the rest of this street she maintained a safe respectable following distance and when we reached the next stoplight she actually stopped a ridiculously long distance to my rear when just a minute earlier she had been tailgating me at 55 mph.

The last mile and a half of the trip was uneventful and pleasant and as I parked to go into the office I decided to spend my lunch hour typing this up and posting it for you. In a few hours it will be time to run the five o-clock five hundred in the 90 degree heat. But I will still enjoy the ride!

Peace Y’all

Revenge of a Junkyard Dog! (Suburban Assault Scrambler Finished!)

It seems hard to believe that it has already been six months since I dragged home a rusty non running 1980 Honda CB650 Custom that I bought sight unseen at a local junk auction for the princely sum of 150 bucks.  If you didn’t see it back then click on this link to see the before pictures. Of course along the way there were various challenges & fun but I had a blast getting this one going and as unlikely a candidate as it was for a scrambler conversion it really did turn out that the whole was greater than the sum of its parts!

Normally I am a man of way too many words so how about if this time I just show you some pictures interspersed with a few tidbits of technical information?

<next to the old yard truck>

1980 Honda CB650 with 1974 Honda CB750 gas tank & a set of 1979 CB650 standard wheels.

<1980 Honda CB650 Scrambler>

1980 Honda CB650 Custom Scrambler

The handlebars are courtesy of a 1970 Honda CL450 I just happen to have lying around. The tires are Shinko 705 adventure touring tires.

<Vintage Honda with vintage plasma cutter>

I wish I had a plasma cutter like this at home!

The green paint is a mixture of gloss green & flat black tractor enamel, & the exhaust is from Mac.

<custom Honda vintage Lincoln welder>

they don’t make machines like this vintage Lincoln welder anymore.

<custom scrambler front forks>

Don’t let the nasty looking lowers fool you, the forks have new seals, Progressive Suspension springs & fresh 10w fork oil. I decided to keep the 650 Custom fork legs for the scrambler conversion since they are longer than the 650 standard forks. When I raised the rear by switching to the 17 inch wheel & taller tire it helped to compensate for the extra rake of the custom and gave more ground clearance.

<kustom 1980 Honda CB650C>

<old Honda with giant press brake>

At this time I would like to give thanks to the wonderful folks who provide me with my day job that makes all of this possible.

Safe Harbor Access Systems for allowing me use of the old warehouse and some production areas for this photo shoot. Click here to see the stuff I spend all day drawing blueprints for! And if you see anything you need let them know where you got the information.

<a green scrambler>

Here’s some more of that headlight bracket drillium that I showed you in my last post.

<1980 CB650C headlight>

speed holes make it faster right?

I couldn’t stand the 85 m.p.h. speedometer that came on this bike, plus it was making a horrible squeaking sound, so on went the 140 m.p.h. speedo & tach from a 1976 CB750F, with green faces of course.

<cb650 engine>

Do you have any idea how hard it was for me not to attack this with the polisher?

K&N air filters hang off the back of the original carburetors, to learn what I did to them just click here. Other than a re-jetting

& a Mac pipe the engine is bone stock in all of it’s 11,000 original mile glory.

<scrambler baby!>

Slug & liquids? Sounds like the results of cheap beer & too many hot wings…

<80 Honda 650 chain guard>

I put a lot of speed holes in this one ’cause I wanted it to be really fast 🙂

Holding up the rear is a set of Progressive Suspension 412 shocks with the heavy duty springs. I have been very pleased with this suspension, it gives a nice cushy ride over some pretty rough bumps but is still firm enough to rock out on a set of curves. Well at least as much as you can with a bike like this.

<honda cb650 with flatbed>

Sometimes you just find the perfect graffiti to really set a picture off.

<Suburban Assaullt Scrambler CB650>

Beware of the Dog

Peace Y’all

‘Psyco

The Fool Tank Chronicles : Part Two

One thing that I have discovered while working on this motorcycle is that deliberately building a rat bike is actually a lot harder than it would seem. In all honesty, a deliberately created rat bike should properly be called a neo-rat bike. A real rat bike is a natural creation, a collection of found art held together by grease, road grime & baling wire that accumulates over decades and tens of thousands of miles. People like my self who drag up old bikes & mechanically restore them while leaving the patina semi-intact are actually just posing. But what the heck it’s a lot of fun! Even so the siren song of the polishing machine, paint gun & steel wool are very hard to resist. Have you ever tried to clean just the inside of a dirty weather-beaten old engine cover and then tried to reinstall it so that it looked as if it had never been disturbed? It ain’t as easy as it sounds. Leave the chrome rusty, oh the horrors! Working hard on your sheet metal & then covering with flat or semi-gloss paint instead of making it shine like a brand new penny is very counter intuitive, but sometimes we really enjoy the results.

<drillium on a CB650>

Here’s some of that exotic metal called drillium.

Now let’s get back to my screwing up a perfectly good tank. As I mentioned in part one the original plan was to cut the rear subframe off and install a custom one for that straight framed 60s & 70s look. When that didn’t happen I took my cut down stock seat & had it recovered in black & green & fitted it to the bike & I actually did my shake down runs and a good bit of commuting on it as it was. Still every time I looked down & saw the bottom edge of the tank was nearly a half an inch above the nose of the seat it bugged me. You see even on a rat, craftsmanship counts. It’s one thing if it has dent’s, rust & flaking paint, but if you modify something or deliberately create a faux patina on something you must do it correctly. For example it’s okay to fog some flat black primer directly over a piece of rusty pitted metal but it is totally unacceptable to get a bunch of paint runs while doing so, because that smacks of sloppy craftsmanship. To me, being my own worst critic, that large seat to tank gap was a sign of very sloppy craftsmanship & it had to go. After experimenting with different thicknesses of rubber isolator for the rear mount I was able to reduce the gap down to about a quarter of an inch. Still too sloppy for me so I took a small body hammer & dolly & started rolling the rear seam of the tank down, figuring that I could repair the green portion of the paint by blending. I actually thought it was going to work but when I was almost finished the seam split. I probably could have silver soldered it closed & coated the tank with a sealer, but my boys kept insisting they did not want to chance a gasoline shower at 60 m.p.h. so it was off to ebay to find another tank.

Buying a gas tank for a motorcycle on ebay can be a very scary proposition. When I was rebuilding the Minimum Ninja, I bought three before I got one that was even usable. The sad part is that I had already left the sellers good feed back before discovering the problems. If I were doing a serious show quality restoration I would do my best to source a N.O.S. tank from a vintage parts dealer before buying one at an online auction. Since this was not a restoration I was hunting functional with a few light dings and no rusted out spots. The one I found looked alright, it had a few visible dings, & some rust on the inside but it was good & solid. I went ahead & put in the rear mounts so it would fit a CB650 this time paying very close attention to how it lined up with the front of the seat.

<bondo bucket gas tank>

arrrgh!

<CB750 to CB650C tank adapter>

<spot putty on top of the primer>

Putty smeared all over the tank & I still missed a couple of spots.

Since it was going to be acid washed & lined to keep the rust out of my gasoline, I decided to strip it down & fix the two or three visible dents on the exterior. Then I started removing the paint to fix dents only to find someone had already fixed a bunch of dents. There was already bondo everywhere! Discouraged I actually got back online & began looking for another tank. The problem is that I had already pre-registered for the Bull City Rumble this coming Saturday. So I just stayed up late last Friday night & fixed everything, acid washed it, put in the tank liner & had it ready to paint first thing Saturday morning.

<1970s Honda CB750 tank w black primer>

the black primer was actually kind of cool looking

Since I was doing all this extra work I wanted a nice durable semi-gloss dark green that was in line with my original vision for this bike. Being an old country boy I really like the Majic brand tractor & equipment enamel, it is a catalyzed enamel that although it has a long initial drying period becomes very durable. The downside is of course that you are limited to tractor & implement colors. But that was okay since I never found an off the shelf semi-gloss paint in the color I wanted anyway. instead I poured some John Deere green into a mixing cup & kept adding matte black until I got the shade & sheen that I wanted.

After seeing how it looked I decided not to put the stripes and the airbrushing back on it this time, in fact I even color matched the emblems before re-installing them late Sunday afternoon after giving the paint 24 hours to dry.

<a green Honda gas tank>

As I sit here writing this on Wednesday the Suburban Assault Scrambler is sitting in the carport, yesterday I put gas in it for the first time with the new tank, and rode it to work today. At lunch time I took a bunch of pictures of the finished product sitting in various industrial locations, but you’ll have to wait a couple of more days for those pics. Then I have to rest a little bit & get ready to start on the next project!

<suburban assault scrambler teaser>

The Fool Tank Chronicles Part 1

Some of us just have to do things the hard way, it’s in our blood and it will not be denied. Take me for example, while by no means wealthy in money I could probably buy any new motorcycle I wanted just sign the dotted line & add another automatic draft to my checking account & ride. But even the new retro bikes don’t have the pull on my soul that the old ones do, they aren’t part of my memories, & they don’t need my love to get back on the road. I don’t know about you, but for me the turning of the wrenches, watching dial gauges & degree wheels, the smell of parts washer fluid & the massaging & painting of old sheet metal bring me just as much pleasure a actually riding the finished product. When I finish one project, or sometimes even before I am constantly scanning Craigslist, Ebay, the local trader papers, & the internet message boards to find the next one.

Sometimes I do very irrational things that create far too much work for myself even by my own masochistic, self flagellating standards. This is the story of how I modified & then destroyed a fuel tank for my CB650 Scrambler project, & then had to fix another one.

Let’s start from the beginning, first there was my junk auction CB650C with this very holey tank.

<original CB650C tank>

As you can see there wasn’t much point in trying to fix that one so I used it for target practice & threw it away. Initially my plan was to turn this bike into a shiny polished cafe racer style custom with a big ’70s tank & some clip-ons, so I ordered up a 1974 CB750 tank from Ebay & set it on the bike just to see how it would look. Of course it wouldn’t work with the stock seat so I broke out the sawzall & cut 2 inches from the front of the seat. At this point I was still planning to cut the rear sub-frame off & put in a tail loop to support a proper cafe racer seat with a bum stop, because I had the Ninja for me & Mrs. Psyco to ride around on two up. Here’s a shot of the initial mock up.

<old 750 tank mockup>

old 750 tank mockup

By the time the above picture was taken fate had intervened in two distinctive ways. First we’ve had one of the wettest, nastiest, stormiest, summers on record. The dirt road that I use to get from my hole down in the swamp out to civilization, has been an almost constant quagmire because we have not been without rain long enough for it to dry completely up. This is not an environment conducive to the cafe racer style of motorcycle as your only bike. The second factor was the sale of the Minimum Ninja, I really wasn’t crazy about selling it, but the gentlemen who bought it from me was like a kid going, “please Santa, I’ll take great care of it I promise,” so I finally gave in & let him have it. To his credit he does keep it much cleaner than I ever did. But now I had to get something rolling & fast, preferably something with two up capacity that would roll down a dirt or gravel road just as good as a paved one. Decide to do a flat green rat bike that require minimum cleaning.

I had already made a new rear tank mount at this time by bending the CB750 mount down & brazing in a sheet metal angle the the proper size hole in it.

cb750 to cb650 rear tank mount clamped

cb750 to cb650 rear tank mount clamped

<cb750 to 650 tank brazed>

My ugly brazing

The problem was that at the time I paid no attention the the seat to tank relation, something that would come back to haunt me later. After I changed my mind about the direction of this project but before really fitting everything together I decided to go ahead & change the color, but since I was doing a “rat bike” style build not to fix any dents or chips & just spray can paint it.

<tank number 1 taped up>

tank number 1 taped up

So I taped off the graphics & cap being careful to trim the tape around the nicks and chips hoping that it would look like the new color was original & spray bombed it with what I thought was a flat dark olive color

<tank after painting>

much lighter than I was expecting:(

About this time, I purchased a “skull pile” stencil from Airsick Stencils & decided to play around with it some, so I popped the tank off & taped it up following the instructions on the Airsick website for using these reversed stencils they sell, & sprayed my main color Createx Wicked Gold.

<airbrushing a gas tank>

This color required a lot more thinner than the other Createx colors I’ve used in the past

After spraying the color I then put the stencil back in place and turned my air pressure down a little bit and sprayed in some opaque black to create the details.

airsick airbrush skullies

laying in the skulls

Here’s what it looks like when you take the stencil off.

<an airbrushed skull pile>

Just In case you were wanting to know the airbrush is a Paasche VL & yes I am very happy with it.

<my Paasche VL airbrush>

After finishing up and giving the paint a few minutes to set up I peeled the tape off.

<peeling back the mask>

peeling back the mask

If you try this at home just remember that most commercially available airbrush paints are designed for fabric use & require heat to set them and make them permanent, so go over the surface with a hair dryer or hot air gun & get it good and warm if you don’t want your paint washing off later.

Most people go back over these skull piles & fill in little details with the airbrush & some freehand stencils. Me I cheated a little bit by doing my detail work with a black extra fine point Sharpie, before spraying on the clear coat.

<closeup of airbrushed skulls>

It looked decent enough for a rat bike I thought

<airbrushed tank on cb650 scrambler>

airbrushed tank on cb650 scrambler

It’s kind of a shame that I destroyed this tank while  attempting to correct the big gap between the bottom of the tank & the top of the seat. Oh well if you’re gonna cook an omelet you gotta break a few eggs. I’ll come back in a day or three and tell you the rest of the story.

I Rode a Segway (& I Liked It!)

<Segway PTs parked at bridge>

Segway PTs parked at bridge on Asheville Greenway

Yes I know the Segway is a nerd toy, but I have wanted to try one ever since they appeared on the scene a few years back. Hey it’s got two wheels & a motor. In fact it has two motors. Sure it’s not as cool as this but it is a whole lot more accessible.

<double engine triumph>

Ok, this is sexier than a Segway, but a whole lot harder to start & turn.

I guess I’m just an oversized heavily muscled nerd who is also a redneck motorcyclist, because I really enjoyed riding this thing on a recent tour around Asheville N.C. This foray into a pleasant couple of hours of geek enjoyment began as I was trying to use up my Marriot Rewards free hotel stay before it expired, so I booked a room at the Courtyard in Asheville & started checking on the internet for tours & guides & saw the Moving Sidewalk Tours website. After checking the very reasonable prices I booked two Segway PTs for the tour, one for me & one for my beautiful, patient, long suffering partner in life. Of course this led to her asking me that question that women have been asking men for thousands of years, “you want me to do what?”. I have invited her to write her own opinion at the end of my review, so be sure to read it too.

Segway Riders

The world famous Heck’s Angels lol

At the beginning of the tour there is a short class to get you acclimated with the operation of the machine. Once you put aside all of your preconceived notions & the instincts that you have developed riding all other two wheeled transportation, the controls become very intuitive.

In one way a Segway is like riding a horse, when you first learn to ride & you step up on the platform it will wiggle & dance under you a little bit. If you are nervous it will reflect that by being a little jiggly when you are trying to be still or start to maneuver. It feels like it is alive under your feet, but quickly settles down once you relax. The simple truth is that it is almost impossible to fall off of one without being really stupid. Just lean your whole body forward to go, & back to stop. For turning you tilt the handle bars in the direction you wish to go. After a few turns around the parking lot our group was ready to go. Our guide Wes was very considerate and the first leg of the tour was down a quiet residential street full of older homes before we ventured uptown to the tourist, shopping, & entertainment district.

One of my preconceived notions about these machines is that they were toys to be used on skating rink smooth surfaces. They handled pavement, sidewalks, & bike trails with aplomb even though these were the street going version, a few bumps and jolts didn’t upset them at all.

All in all this is a great machine, especially for a city dweller who works & shops within a few miles of home. Sure the top speed is only about 12.5 mph or so, but the view standing up on the platform above everything else on the street or sidewalk is terrific. The range is rated at 24 miles & I am inclined to believe that unlike some electric vehicles that it is an honest number.

Now I just got to try one of the off-road versions somewhere! Perhaps the company should send me one for a long term evaluation. 😉 I swear I’ll take good care of it and let everyone in the world know if it’s any good or not.

Peace Y’all

And Now It’s Time For Mrs. Psyco’s Opinion!

After my initial shock that we were going to be riding on these contraptions, I said to myself they can’t be that hard to ride so I made up my mind that I would try. Then we meet the other couple that was going to ride with us and they were much older than we are and they said it was so easy, so I was really ready to go. But when I stepped on it, it went to wiggling and I tried to get off but I couldn’t keep it still, so I said help me I can not do this, I want to get off. So Wes helped me off and I looked back at Floyd and I saw that he had it figured out. I decided to try again and after trying several times and being  told to relax and not to hold on so tight I finally got it. It took me between five and ten minutes and then I was on my way loving it and feeling so carefree. What a rush!

Thanks to Moving Sidewalk Tours for an enjoyable afternoon.

The 2013 AMCA Southern National Meet!

Indian Chief

A fantastic motorcycle but just a little out of my price range.

This was the first time I have attended this event, the AMCA Southern National Meet. I went on Saturday & had to duck a few showers in the morning but other than that it was a great day! There were some truly outstanding motorcycles on the grounds along with a few neat old bicycles too. Here are a few of the pictures I took around the show grounds, enjoy!

Schwinn Cycle Truck

Kinda Rough & Crusty

Ross badge on Schwinn Cycle Truck

I have no idea why it had a Ross head badge on it.

<neat little bobber>

Triumph in a Bubble!

Triumph in a Bubble!

antique Harley with a saddle

Giddy Up!

Triumph Cubs

Triumph Cubs Hard to resist!

Vintage Vespa & old moped.

Vintage Vespa & old moped.

Carbide Bike Headlight

Who doesn’t love an old bicycle?

rusty Monark Super Twin

rusty Monark Super Twin

BSA Motorcycle

A nice ride able BSA!

antique Benelli 2 stroke

antique Benelli 2 stroke

another great vintage Triumph

I really enjoy seeing bikes like this Triumph Scrambler getting ridden. instead of merely displayed.

another nice old hog

old Harley with bare sheet metal

BSA B50MX

BSA B50MX

crusty project for sale

crusty project for sale

<old motorcycle>

The theme for this year was British Iron and the were some first class examples placed inside of one of the exhibition halls.

Ariel Square Four

Ariel Square Four

A Magnificent Triumph

A Magnificent Triumph

beautiful restored Vincent

beautiful restored Vincent

 cool custom Bonneville

cool custom Bonneville

AJS all decked out for touring

AJS all decked out for touring

Harley Davidson Sprint

I would like to have one of these

1960 Triumph Thunderbird

my dream machine

1960 Triumph Thunderbird

fantastic looking engine

Thunderball BSA

Thunderball BSA

<BSA Thunderball>

Cushman Eagle V2

Cushman Eagle with v twin engine

 coolest dog at the show

coolest dog at the show

Harley K model

Harley K model this would be a great restoration project

<Harley K>

kool tow trucks

kool tow trucks #1

kool tow trucks #2

kool tow trucks #2

field events pictures

field events pictures

Cushman in plank  race

Cushman in plank race

winner of the plank race

winner of the plank race

slow race

slow race

slow race

slow race

immaculate Moto Guzzi Eldorado

immaculate Moto Guzzi Eldorado

immaculate Moto Guzzi Eldorado

Moto Guzzi Eldorado another of my dream bikes

Briggs and Stratton motor wheel

Briggs and Stratton motor wheel

This was the first time I had ever seen a Briggs & Stratton  motor wheel. Neat old piece. The same gentleman also had the Smith motor wheel pictured below.

Smith motor wheel

Smith motor wheel

This event is held each year at Denton Farm Park in Denton, N.C. This is a fantastic venue for events of this type check their website for a schedule of different interesting events throughout the year.

Adventureism The April Website of the Month!

A fellow WordPress blogger named Jesse Mckay is getting read to head off on a coast to coast to coast ride (He’s starting from Corpus Christi, Texas) on April 29th.

Click here to check out his blog at  http://twowheelin.wordpress.com/. 

This gentleman has a lot of that good do it yourself spirit that used to be universally prevalent amongst motorcyclists. Check out his Buell Blast modification page too. At any rates let’s all wish him a safe, happy trip & follow along on the ride.!

Again the link is http://twowheelin.wordpress.com/

The 2013 Charlotte International Motorcycle Show Part 2!

Nicky Hayden #69 Ducati Corse 1000cc

Nicky Hayden #69 Ducati Corse 1000cc

Welcome to the second installment of my pictorial review of the Charlotte International Motorcycle Show.  For the second post I have actually decided to treat this as a product review, because in a sense that is exactly what the IMS series is, a product produced to entertain and inform motorcycle enthusiasts.

I thought Mahindra made tractors

I thought Mahindra made tractors

Danny Webb #99 Mahindra 250cc

Danny Webb #99 Mahindra 250cc

There were displays from all of the major manufactures except for Kawasaki & Yamaha. This did lead to a lot of Facebook grumbling from fans of these two marques. Yes I wish they had arranged to be there, but in this economy it is understandable that some companies have had to curtail such activities. Still there was plenty to see. Harley Davidson even brought in their “demo bike on a treadmill” setup for people to try. The Polaris Corporation set up a display for their recently acquired Indian brand. Of course the first one I made a beeline for was the Ducati display!

One of those stunning Ducati Girls

One of those stunning Ducati Girls

The boys from Ton Up N.C. had a fantastic club display with a couple of Tritons and some other fine vintage iron, for everyone to admire. On the other side of the hall were the Antique Motorcycle Club of America, and the Vintage Japanese Motorcycle Club.

Moto Guzzi V7 Racer

Moto Guzzi V7 Racer

Moto Guzzi V7 Racer

Moto Guzzi V7 Racer

Honda CB1100

Honda CB1100

Two of the vendors there were for the new lithium technology batteries. I was so impressed with this technology that I have actually become a dealer for the Shorai LFX line so be sure check back here soon as I will be setting up an online store to sell them and will have a link and review posted here.

There were some leather & t-shirt vendors, & of course lots of insurance companies. We got to check out a lot of new lids jackets etc.

Honda CB1100

Finally the retro bike we’ve all been waiting for!

The XDL Street Jam show was worth the price of admission all by itself. I greatly enjoyed trying the “Pit Stop Challenge” contest which involved changing the rear tire on a Grand Prix race bike, my time was 24 seconds by the way. And of course as you can tell from my pictures the custom bike show was awesome.

Whiskey Tango 650 Yamaha Chopper

Whiskey Tango 650 Yamaha Chopper

Tennesee Rose 650 Yamaha Chopper

Tennessee Rose 650 Yamaha Chopper

Tennesee Rose 650 Yamaha Chopper

Details,details, details!

Arlen Ness Digger

Arlen Ness Digger

another Whiskey Tango XS650

another Whiskey Tango XS650

a bad ass BSA

So many super cool details on this BSA.

Joe Hunt Magneto

When was the last time you saw one of these?

And now for my favorite group the custom crotch rockets.

JDA Custom Suzuki Hayabusa

one of 2 Suzuki Hayabusa Sweepstakes bikes!

Garwood Customs Suzuki Hayabusa

The other Suzuki sweepstakes prize.

Speedworx Enterprize 2009 Honda CBR1000

Speedworx Enterprize 2009 Honda CBR1000

Speedworx Enterprize 2009 Honda CBR1000

Fantastic from any angle

Black Widow Suzuki Hayabusa

Black Widow Suzuki Hayabusa

Black Widow Suzuki Hayabusa

Black Widow Suzuki Hayabusa

95 Suzuki Katana

Now this is a Kan-o-tuna. The 1100cc motor turns it into a shark.

Out of all the Harleys there my favorite was this give away Sportster built by Roland Sands.

RSD Sporty

I’ll take mine in flat black please…

Regardless of what a few whiners on the net have said it was well worth 15 bucks. Hell earlier this year I paid $20 to go to local show that was so dead I left after 20 minutes so to me this one was fantastic. Yes it could have been better; I personally would have liked to have seen more club or custom shop displays, and since there was plenty of space left in the Convention Center an open custom & vintage motorcycle show in addition to the invitation only J&P Cycles Ultimate Custom Builder show.

<Charlotte IMS>

Mrs. Psyco & I actually sprang for the VIP tickets. It worked out great for us since we are early risers anyway. We got in early & had a little guided tour & got a preview of the XDL show so to me it was definitely worth the extra money, especially since I was pushing my lovely wife around in a wheelchair due to a very badly sprained ankle. We’ll be going back next year.

Even with the giant insurance commercial that dominated a large area of the floor (don’t bitch if Progressive didn’t sponsor this event it probably wouldn’t happen at all), this was still a great way to kill a few hours & meet lots of interesting people and learn about new motorcycles and accessories. So it was worth the few bucks to get in & I am happy to recommend that you try to attend one near you next year.

The 2013 Charlotte International Motorcycle Show Pg.1

<XDL Street Jam at Charlotte International Motorcycle Show>

XDL Street Jam at Charlotte International Motorcycle Show

Hello Dear Readers,

Last weekend the lovely Mrs. Psyco and I attended the 2013 Progressive International Motorcycle Show at the Charlotte Convention Center in Charlotte N.C. Since it was my first time attending this show I wanted to share my experiences with you. We are morning people and like to pretend we are children of privilege so I sprung for the early admission VIP tickets. This worked out very well for us as two weeks ago my lovely wife slipped and fell in the kitchen on our way out the door. It turns out that some ladies shoes are probably far more dangerous than motorcycles. The first picture above is from the XDL Street Jam show.

motopsyco on a 2013 Ducati Diavel

The Diavel made me do it!

A couple of years ago one of my very first blog posts was about the introduction of the then brand spanking new Ducati Diavel. Well I finally got to see one in the flesh and throw a leg across it. It fit very well and everything seemed to fall perfectly into position for me, plus with my but firmly on the seat I was able to put my feet flat on the floor. Now I really gotta go get a demo ride on one. The fine people at Ducati Greensboro provided the bikes on display at the show.

The Nelsonore Custom 76 Honda CB750

Gary Nelson’s Cafe/ Scrambler CB750 was my favorite bike at the show.

Moving on to the show bikes in the J&P Cycles Ultimate Custom Builder contest. The above 76 Honda CB750 is the coolest thing I have ever seen. At the risk of sounding conceited I’ll confess that up until now my all time favorite was my very own Yamaha XT600 supermoto that I featured in an earlier post. But Gary Nelson is one of the most talented vehicle engineers to ever live. Just look at all of his work in NASCAR. No wonder this is my new favorite custom motorcycle of all time.

The Brew Racing CB350 Racebike

The Brew Racing CB350 Racebike

In 2011 Brew Racing Frames was my listing as website of the month for December. Nothing is more awesome than seeing a genuine for real racing motorcycle entered in a show like this against all of the pampered show bikes. Enlarge the picture below for it’s racing pedigree.

Brew Racing CB350 Credentials

Brew Racing CB350 Credentials

Triumph Scrambler

Triumph Scrambler

Here are a couple of beautiful bikes from the Triumph display, one new & one old.

classic rigid frame Triumph

nothing classes up the joint like a beautiful old Triumph.

One of the most interesting things on display was the Tharo EV Scooter by a division of Tharo Systems.  It does have a much more realistic MSRP (around $4200 or so) than most big electric scooters.

Tharo EV electric scooter

Tharo EV electric scooter

Of course since I just love old rice grinders the VJMC booth was my favorite club/vendor display stand at the meet.

Check out this old CL450 Scrambler.

Check out this old CL450 Scrambler.

There’s a soft spot in my heart (or is it in my head?) for old scramblers of any make.

Honda CBX1000 six cylinder

Honda CBX1000 six cylinder

The six cylinder Honda CBX was the epitome of early ’80s muscle bike development. But with introduction of the GSXR soon to come the original musclebike era came to a close in the mid “80s with only the Mighty V Max soldiering on alone until the beginning of the 21st century.

side view of CBX

side view of CBX

That’s all for now, but check back soon as  I will post some more pics and my analysis of the good things, and the shortcomings of the show.

HANG IN THERE, SPRING IS COMING!

Ninja EX250

lunchtime Jan. 16, 2013

 

This is for all of my friends in colder places. It is my lunch break, it is 73 degrees farenheit in January, and this is my motorcycle parked outside of my office. I’m not trying to rub it in, just wanted to share a little joy with you today!

Peace Y’all